This tut is written for those with a basic knowledge of psp. I use psp 10.
Supplies needed:
Mask: WSL_Mask7 from weescotslass.
Tube of choice. I used the artwork of Ismael Rac which can be purchased here: XeracX
Scrap kit: Rock-a-billie from Pimp'd Designs.
----------------------
Let's get started :)
Gather your supplies and open your psp.
Open mask in psp and minimize.
Open a new file size 600 x 600 pixels.
Flood fill bottom layer with white.
Take paper 05, paste as a new layer.
Go to Layers - New Mask Layer - From Image - select mask from list.
**Make sure invert mask data is not checked**
Merge layer group.
Paste glitter 04 above the merged layer.
Paste frame 02 above the glitter layer.
Resize frame to 80%.
Using magic wand tool, select inside frame.
Go to Selections - Modify - Expand - 5.
Paste paper 4 below frame.
Invert selection (ctrl/shift/I) then hit delete, and select none (ctrl/D).
Paste banner 01 above frame 02.
Rotate it to the left and position near the upper left corner of the frame.
Resize it to your liking and give drop shadow.
Paste frame 01 as a new layer above frame 02.
Using magic wand tool, select inside one of the sections of frame 01.
Go to Selections - Modify - Expand - 5
Paste paper 01 below frame 01.
Invert selection (ctrl/shift/I) then hit delete, and select none (ctrl/D).
Go back to frame 01.
Using magic wand tool, select inside the other section of the frame.
Go to Selections - Modify - Expand - 5.
Paste paper 01 (or another of your choice) below frame 01.
Invert selection (ctrl/shift/I) then hit delete, and select none (ctrl/D).
Paste glitter 02 below frame 01.
Resize to your liking and position in the right section of the frame.
Use your eraser tool to take off any edges that show outside frame section.
Go to Layers - Properties - Opacity = 80.
Paste flames 01 above frame 01.
Resize to your liking and position in the left section of the frame.
Use your eraser tool to take off any edges that hang below the bottom of that frame section and some of the flames between the two frame sections to give the look of overlapping. (See my tag for idea)
Paste bolts above frame 01.
Resize to your liking and position to the right side along the edge of the frames.
Paste staple above bolts.
Resize to your liking and position to the to the right side of tag where the two frames overlap.
Repeat this on the left side of the tag.
Paste your tube above staple.
Resize and position over right section frame 01.
Give tube a drop shadow.
Add any other elements you'd like to tag.
Resize if needed and add drop shadows.
Crop and resize tag to your liking (if you prefer a smaller tag).
Add your name at the bottom of tag.
(I used 2Peas Wedding Day font at 150 pixels)
Apply drop shadow.
Add in any artist, copyright, & license info.
Voila! Your tag is done.
Supplies needed:
Mask: WSL_Mask7 from weescotslass.
Tube of choice. I used the artwork of Ismael Rac which can be purchased here: XeracX
Scrap kit: Rock-a-billie from Pimp'd Designs.
----------------------
Let's get started :)
Gather your supplies and open your psp.
Open mask in psp and minimize.
Open a new file size 600 x 600 pixels.
Flood fill bottom layer with white.
Take paper 05, paste as a new layer.
Go to Layers - New Mask Layer - From Image - select mask from list.
**Make sure invert mask data is not checked**
Merge layer group.
Paste glitter 04 above the merged layer.
Paste frame 02 above the glitter layer.
Resize frame to 80%.
Using magic wand tool, select inside frame.
Go to Selections - Modify - Expand - 5.
Paste paper 4 below frame.
Invert selection (ctrl/shift/I) then hit delete, and select none (ctrl/D).
Paste banner 01 above frame 02.
Rotate it to the left and position near the upper left corner of the frame.
Resize it to your liking and give drop shadow.
Paste frame 01 as a new layer above frame 02.
Using magic wand tool, select inside one of the sections of frame 01.
Go to Selections - Modify - Expand - 5
Paste paper 01 below frame 01.
Invert selection (ctrl/shift/I) then hit delete, and select none (ctrl/D).
Go back to frame 01.
Using magic wand tool, select inside the other section of the frame.
Go to Selections - Modify - Expand - 5.
Paste paper 01 (or another of your choice) below frame 01.
Invert selection (ctrl/shift/I) then hit delete, and select none (ctrl/D).
Paste glitter 02 below frame 01.
Resize to your liking and position in the right section of the frame.
Use your eraser tool to take off any edges that show outside frame section.
Go to Layers - Properties - Opacity = 80.
Paste flames 01 above frame 01.
Resize to your liking and position in the left section of the frame.
Use your eraser tool to take off any edges that hang below the bottom of that frame section and some of the flames between the two frame sections to give the look of overlapping. (See my tag for idea)
Paste bolts above frame 01.
Resize to your liking and position to the right side along the edge of the frames.
Paste staple above bolts.
Resize to your liking and position to the to the right side of tag where the two frames overlap.
Repeat this on the left side of the tag.
Paste your tube above staple.
Resize and position over right section frame 01.
Give tube a drop shadow.
Add any other elements you'd like to tag.
Resize if needed and add drop shadows.
Crop and resize tag to your liking (if you prefer a smaller tag).
Add your name at the bottom of tag.
(I used 2Peas Wedding Day font at 150 pixels)
Apply drop shadow.
Add in any artist, copyright, & license info.
Voila! Your tag is done.
No comments:
Post a Comment